Crystal Clear Epoxy – 1 Gallon Combined Bar/ table top, Small Casting and crafts

Description

1 Gallon Table Top & Bar Top Epoxy Resin, Small Castings, Ultra Clear Finish
(Free shipping to U.S. and Puerto Rico)
ALERT!!!! PLEASE READ- Epoxy Resin is in short supply and industry prices are soaring due to lack of ingredients. Good news is we have inventory and are offering a new and improved version as of 6/11/2021. NEW and IMPROVED formula includes these benefits. Longer work time (approximately 35 minutes), greater resistance to yellowing, less micro bubbles created for clearer molds and you can now pour up to 3/4 inch thick. Please reach out to us if you have any questions about how our product will work with the project that you are doing.
f placing a larger order please send us a message before ordering and if you have any questions. Smaller orders should be processed as normal.
GENERAL PURPOSE CLEAR EPOXY RESIN
.
We are a family owned small business based out of Temecula California. Our main goal is to provide a quality product at a fair price and offer excellent customer service.
IF YOU SEE OUR BRAND SELLING FOR $13 -$9- $7  OR OTHER CRAZY PRICES FROM SOMEONE ELSE THEN THAT ACCOUNT IS FRAUDULENT. UNLESS it is one of our auctions starting price.
Perfect for
tabletops
,
bar tops
,
jewelry/craft making
,
coasters
,
small castings
(under 2″ thick with several 3/4 inch pours),
some marine applications, pebble coatings and much more.
Please Note
:
This kit is one gallon in total
.  Kit includes 1/2 gallon of Resin and 1/2 Gallon of Hardener. Packaged by
weight
. Resin weight is 4.10 pounds and the hardener weight is 3.14 pounds. This formula works great for a wide variety of applications.
Easy mix
at 1:1 ratio by volume, long work time, with great clarity and a high gloss finish. Cures rock hard and is scratch resistant. Excellent chemical and water resistance(s), coupled with superb mechanical properties, make this resin a candidate for all applications.
3/4 inch pour is maximum at one time.
Important:
With this resin the thin
Hardener
must be poured
FIRST
and then the thicker Resin into the hardener. Then mix well for 5 minutes.
Properties
:
Mix Ratio…………………..1:1 by volume
Work time ……………………..35 minutes (200gram mass)
Hardness……………………………D78
Mixed Viscosity……………………..1200cps.
Chemical Resistance…………….excellent
Moisture Resistance……………excellent
Product weight………………..8 pounds
1/2 inch pour is maximum at one time
Cure Times / Speed
Typical work time on this item is roughly 35 minutes based on mass and temperature.  Thin film set time (3mil. film) is roughly 5 hours at 78F.  Full cure is 24 hours at normal conditions. Work environment must be between 72 to 85 degrees Fahrenheit.
This product cures to a brilliant high gloss finish.  The finished product will be very solid, smooth, clear, and display a brilliant high gloss finish similar to glass.
Mixing, Storage, and Application
Mix this resin 1:1 by volume using a measuring cup.  Precise Measurement Required. Do Not Pour Entire Bottles Together Without Measuring First. If mixing by weight reach out to us for instructions.  When mixing this product, make sure to use a round cup & mix thoroughly scraping all sides and bottom of mixing container.  Improperly mixed epoxy can create a major headache.  Remember that thermoset plastics are temperature sensitive.  Cold weather slows the cure process down, whereas heat speeds curing up. This epoxy likes warm temperatures (72 degrees and above). Always mix chemicals at room temperature and warm the bottles first.  For BEST results you MUST pour the hardener (B) into the mixing cup
FIRST
and then pour the epoxy (A) second..  Pour along the side of the container to help alleviate air entrapment.  Mix for at least 3-5 minutes in a in a round motion until chemical are clear and free of striations.  Allow the mixed components to stand in your mixed cup for at least 5 minutes.  This allows for bubbles to rise to the surface.  Small castings and potting units may take longer to cure than larger items.
3/4 inch pours are the maximum with this product. Not a deep pour product. And Again Do Not Just Pour the Two Bottles Together Without Measuring.
Pro Tips —
Warm the resin and hardener before mixing.
Use heat gun or torch to eliminate bubbles.
Keep working area at least 72-75 degrees Fahrenheit. Resin can be very sensitive to colder temperatures.
Watch lots of YouTube videos on how to use Epoxy Resin
Mix SLOWLY and extremely well.
Do NOT scrape product out of the mixing cup into your project. Just use what flows out freely. Unmixed product sticks to the sides and you don’t want that in your project.
When in doubt pour into second mix cup and mix again.
Practice to see how the product works before pouring on your final project.
This chemical needs to be stored in a dry, safe, temperature controlled environment.  Always keep the lids tightly sealed when not in use.  Remember, oxygen can oxidize and can rapidly degrade the epoxy and hardener.  Moisture is also a potential issue.  Always keep the bottles sealed when not in use.
Always Be Safe:
When applying this product, use gloves, goggles, respirator and proper safety equipment.  Please refer to the safety data sheet before using any of our epoxy products.
Product has approximately a 1 year shelf life from the time of purchase if unopened. 3-6 months if opened.
SHIPPING
:
Our warehouse ships items within 1 business day of order.  Maximum of 10 gallons shipped to one customer during shortages. We ship USPS and will forward all tracking information once your item has shipped.  Please be advised that our normal business hours are Monday to Friday.  USPS usually has 1-3 day transit.
RETURNS:
Our goal is to provide quality products and keep our customers happy.  If you are not satisfied with your purchase, we will issue you a full refund. We do ask that the buyer pays for return shipping.